Harman Kardon Avr 165 Manual

Sidney Harman and Bernard Kardon invented the receiver, a single component designed to simplify home entertainment without compromising performance. Over the years, Harman Kardon products have become easier to use while offering more features and sounding better than ever.

To obtain the maximum enjoyment from your new AVR, please read this manual and refer back to it as you become more familiar with its features and their operation.

If you have any questions about this product, its installation or its operation, please contact your Harman Kardon retailer or custom installer, or visit our Web site at www. The following accessory items are supplied with your AVR. If any of these items are missing, please contact your Harman Kardon dealer, or Harman Kardon customer service at www. To avoid safety hazards, use only the power cord supplied with your unit.

We do not recommend that extension cords be used with this product.

Revista proceso n 1926 pdf printer

As with all electrical devices, do not run power cords under rugs or carpets, or place heavy objects on them. When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. If you do not intend to use your AVR for any considerable length of time, disconnect the plug from the AC outlet.

View Harman Kardon AVR 165 Service Manual online

There are no user-serviceable components inside this product. If water or any metal object such as a paper clip, wire or staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service center. If an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges. If you install the AVR in a cabinet or other enclosed area, provide cooling air within the cabinet.

Under some circumstances, a fan may be required.

Manual Speaker Setup

If a short circuit is not found, bring the unit to an authorized Harman Kardon service center for inspection and repair before using it again. IR sensor: This sensor receives infrared IR commands from the remote control. It is important to ensure that the sensor is not blocked. Set button: Press this button to select the currently highlighted menu item. Message display: Various messages appear in this two-line display in response to commands and changes in the incoming signal.

In normal operation, the current source name appears on the upper line, while the surround mode is displayed on the lower line. When the on-screen display menu system OSD is in use, the current menu settings appear. Surround-mode availability depends on the nature of the source input signal, i. Volume knob: Turn this knob to raise or lower the volume.

Tuning Mode button: This button toggles between manual one frequency step at a time and automatic seeks frequencies with acceptable signal strength tuning mode. It also toggles between stereo and mono modes when an FM station is tuned in. Channel Level Control button: Press this button to activate the channel-level adjustment feature. Digital Input button: Press this button to change the audio input for the current source.

Edit pdf on ipad 2012

Although you can assign any digital audio input to any source, the analog audio inputs are all permanently dedicated to the source with which they are labeled. When the radio is the active source, use these buttons to tune stations according to the setting of the Tuning Mode button see above. Surround-Mode Category button: Press this button to select a surround-sound category. See Audio Processing and Surround Sound, on page 20, for more information on surround modes.

Source Select buttons: Press these buttons to select the active source. USB port: You can use this port to perform software upgrades that may be offered in the future. Do not connect a storage device, a peripheral product or a PC here, unless instructed to do so as part of an upgrade procedure.

Aux Analog Audio Input connector: Connect an auxiliary source component that will be used only temporarily, such as a camcorder, portable music player or game console, here. If your source devices have HDMI connectors, using them will provide the best possible video and audio performance quality.

Since the HDMI cable carries both digital video and digital audio signals, you do not have to make any additional audio connections for devices you connect via HDMI connections. See Connect Your Source Devices, on page 13, for more information. You will also need to make an audio connection from the player to the AVR.

You can record any composite video input signal. You will also need to make an audio connection from the source device to the AVR. See Connect IR Equipment, on page 15, for more information.

Insert the plug until it snaps into place in the connector. Subwoofer connector: Connect this jack to a powered subwoofer with a line-level input. See Connect Your Subwoofer, on page 13, for more information.

AVR 165 — Harman Kardon Audio Service Manual (repair manual)

Speaker connectors: Use two-conductor speaker wire to connect each set of terminals to the correct speaker. See Connect Your Speakers, on page 13, for more information. You can record both coaxial and optical digital PCM audio signals. It is usually left on and cannot be turned on or off using the remote control. It can be used to turn on and off other devices such as a powered subwoofer.

Harman-Kardon AVR 165, AVR 1650 User Manual

AC Input connector: After you have made all other connections, plug the supplied AC power cord into this receptacle and into an unswitched wall outlet. During the installation process, you may program the codes for each of your source components into the remote. See Table A10 in the Appendix for listings of the functions for each type of component.

Due to the wide variety of functions for various source devices, we have included only a few of the most often-used functions on the remote: alphanumeric keys, transport controls, television-channel control, menu access and power on and off.

IR Transmitter lens: As buttons are pressed on the remote, infrared codes are emitted through this lens. To restore the sound, press this button or adjust the volume. Source Selector buttons: Press one of these buttons to select a source device, e. Each successive press changes the band.

Best business studies reference book for class 12

Test Tone button: Press this button to activate the test tone for calibrating channel volume levels by ear. OSD button: Press this button to activate the on-screen display menu system.

Channel Level Control button: Press this button to activate the individual channel-level adjustment. It lets you easily change the channel balance to suit different programs or seating arrangements. See Manual Speaker Setup, on page 21, for more information. OK button: This button is used to select items from the menu system. Lip-sync issues can occur when the video portion of a signal undergoes additional processing in either the source device or the video display.

Number buttons: Use these buttons to enter numbers for radio-station frequencies or to select station presets. Tuning Mode button: Press this button to toggle the radio between manual one frequency step at a time and automatic seeks frequencies with acceptable signal strength tuning mode. Memory button: To save the currently tuned radio station as a preset, press this button, then a Number button. Direct Station Entry button: Press this button before using the Number buttons to enter a radio station frequency.

Clear button: Press this button to clear a radio station frequency you have started to enter.

Depending on whether the tuning mode has been set to manual or automatic, each press will either change one tuning frequency increment at a time or seek the next higher or lower station with acceptable signal strength.

Tone Control button: Press this button to access the bass and treble controls. Disc Skip button AVR : This button is used with some optical disc changers to skip to the next disc.

Night Mode button: Press this button to activate Night mode with specially encoded Dolby Digital discs or broadcasts. Night mode compresses the audio so that louder passages are reduced in volume to avoid disturbing others, while dialogue remains intelligible.

Each press of the button advances through the following settings:. Loud passages in the program remain as they were recorded. Macro buttons: These buttons may be programmed to execute a series of up to 19 commands with a single button press.

They are useful for programming the command to turn on or off all of your components or for accessing specialized functions for a different component from the one that you are currently operating. See Programming Macro Commands, on page 24, for information about programming macros. Transport Control buttons: These buttons have no effect on the AVR but are used to control many source components.

This introductory section will help you to familiarize yourself with some basic concepts unique to multichannel surround-sound AVRs, which will make it easier for you to set up and operate your AVR. A system with more than two speakers is called a multichannel system.

Download Harman Kardon AVR 165 Service Manual (Repair Manual)

The different main speaker types in a home theater system are:. In many surround-sound modes, these speakers are secondary, while the main action, especially dialogue, is reproduced by the center speaker. Many people expect the surround speakers to play as loudly as the front speakers.

Although you will calibrate all of the speakers in your system to sound equally loud at the listening position, most artists use the surround speakers for ambient effects only, and they create their programs to steer relatively little sound to these speakers.

It augments smaller, limited-range main speakers that are usually used for the other channels. Many digital-format programs, such as movies recorded in Dolby Digital, contain a low-frequency effects LFE channel that is directed to the subwoofer. The LFE channel packs the punch of a rumbling train or airplane, or the power of an explosion, adding realism and excitement to your home theater.

Some people use two subwoofers for additional power and for even distribution of the sound. A variety of algorithms have been developed in an effort to recreate the way we hear sounds in the real world, resulting in a rich variety of options.

Harman kardon avr 165 manual

Several companies have developed different surround-sound technologies, all of which can be accurately reproduced by your AVR:. Appendix Table A9, on page 31, contains detailed explanations of the different surroundsound options available on your AVR. Other surround modes may be used with digital and analog signals to create a different surround presentation or to use a different number of speakers.

Surroundmode selection depends upon the number of speakers in your system, the programs you are watching or listening to, and your personal tastes. Use the illustration below as a guide for 5.